Explosion-protected floodlights are hazardous locations for the presence of flammable gases and dust. They can prevent arcs, sparks, and high temperatures inside the lamp from igniting flammable gases and dust in the surrounding environment, thereby meeting explosion-proof requirements.
Application scope:
1. Suitable for hazardous areas in explosive atmospheres Zone 1 and Zone 2;
2. Suitable for IIA, IIB, IIC explosive gas environment;
3. Suitable for flammable dust environment 20 area, 21 area, 22 area.
Instructions:
According to the actual needs of the work site to determine the lighting installation location and method, and then according to the distance from the lamp to the power contact to prepare the corresponding length of Φ8 ~ Φ14mm three-core cable.
Open the end cap of ballast, loosen the pressing nut of the ballast cable inlet, and lead the lamp cable and power cable through the compression nut to the internal terminal of the ballast, connect and fix, and tighten separately. Cables tighten nuts and tighten ballast end caps.
According to the determined installation location and method, the lamps and ballasts are installed, and the other end of the input cable of the ballast can be connected to the 220V power supply according to the requirements of explosion-proof.
Loosen the screws at the bottom of the lamp holder bracket, and adjust the lighting position by rotating 360° around the lamp holder; loosen the screws on both sides of the lamp holder, adjust the lighting angle of the lamp holder up and down according to the lighting requirements, and then fasten the screws.
When replacing the lamp, use a suitable screwdriver or other tool to insert the front cover into the holes on the two front side of the front cover, remove the bad lamp, and replace the new one.
Precautions:
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When installing and maintaining the lamp, you must disconnect the power supply.
3, when used, the surface of the lamp has a certain temperature rise, which is a normal phenomenon; the temperature of the center of the transparent part is relatively high and must not be touched.
4. When replacing the bulb, use the bulb of the same type and power; if you change the bulb type or power, replace the matching ballast accordingly.
Application scope:
1. Suitable for hazardous areas in explosive atmospheres Zone 1 and Zone 2;
2. Suitable for IIA, IIB, IIC explosive gas environment;
3. Suitable for flammable dust environment 20 area, 21 area, 22 area.
Instructions:
According to the actual needs of the work site to determine the lighting installation location and method, and then according to the distance from the lamp to the power contact to prepare the corresponding length of Φ8 ~ Φ14mm three-core cable.
Open the end cap of ballast, loosen the pressing nut of the ballast cable inlet, and lead the lamp cable and power cable through the compression nut to the internal terminal of the ballast, connect and fix, and tighten separately. Cables tighten nuts and tighten ballast end caps.
According to the determined installation location and method, the lamps and ballasts are installed, and the other end of the input cable of the ballast can be connected to the 220V power supply according to the requirements of explosion-proof.
Loosen the screws at the bottom of the lamp holder bracket, and adjust the lighting position by rotating 360° around the lamp holder; loosen the screws on both sides of the lamp holder, adjust the lighting angle of the lamp holder up and down according to the lighting requirements, and then fasten the screws.
When replacing the lamp, use a suitable screwdriver or other tool to insert the front cover into the holes on the two front side of the front cover, remove the bad lamp, and replace the new one.
Precautions:
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When installing and maintaining the lamp, you must disconnect the power supply.
3, when used, the surface of the lamp has a certain temperature rise, which is a normal phenomenon; the temperature of the center of the transparent part is relatively high and must not be touched.
4. When replacing the bulb, use the bulb of the same type and power; if you change the bulb type or power, replace the matching ballast accordingly.
Most of the Safety T-Shirt are constructed from the high performance, lightweight and quick drying brideyes fabric, which is specially designed to allow increased airflow and helps to maintain a balanced core bady temperature, the fabric is durable and keeps its shape well. All of our styles are cleverly designed with strategically positioned reflective tapes which allow for garment stretch and optimal wearer movement. The reflective tape of this kind of vest can be hot patch or sewed.
Safety T-Shirt,Reflective T-Shirt,Safety Shirts,Safety Yellow Shirts
Xinxiang Zhongke Reflective Material Co., Ltd. , https://www.safetyvest.pl