After the attack of the super typhoon "Weimason", the homes of many residents in Haikou and Wenchang in our province have been soaked in the water. Home experts reminded that although the accumulated water has gradually subsided, the residents still can't take it lightly, and should deal with the soaking floor in time, which can effectively avoid the trouble of re-laying the floor.
Strengthening the floor soaking water is recommended to naturally evaporate
Because the laminate flooring has the characteristics of easy care, wear resistance, non-deformation after laying, good impact resistance and flame retardancy, it is well received by consumers. Master Chen, who has rich experience in floor maintenance, said that the waterproofing of the floor is higher than that of other floors. Usually the water is poured on the floor, as long as the surface is dried as soon as possible.
After strengthening the floor soaking water, remove the furniture on the floor, try not to press the pressure, and quickly drain the surface water. Then remove the skirting line at the edge of the floor as soon as possible, revealing the expansion joint of the floor, and dispersing the water vapor by the expansion joint. "Do not Pick up the floor to dry, which will cause damage to the floor and may not be used again." The master reminded.
Depending on the degree of soaking water, it usually takes about seven to fifteen days to completely dry. For floors with good quality or short water immersion time, it can be recovered by itself. If it is found that the lifting or flatness cannot be recovered after fifteen days, it should be considered. Replace it again. Master Chen suggested: "If there is a lifting deformation after the floor is soaked in water, it is best to replace it. It is not recommended to plan the part of the arch and repaint it, because it will lead to inconsistency with other plates, and the whole The thickness of the wooden board is uneven, the force is different, and pits are prone to occur."
Solid wood floor soaked in water "well" stacked on the dry
Solid wood flooring is made of pure solid wood, which preserves the natural properties of wood: it is easy to absorb water and deform. After the solid wood floor is immersed in water, the surface water should be dried as soon as possible. At the same time, the vacuum cleaner should be pointed at the splicing gap of the immersed floor to absorb the water vapor. Or use a hair dryer to blow the seam with cold air until it is blown dry, but avoid blowing it with hot air to prevent the surface from being cracked due to heat drying.
If the solid wood floor is immersed in water for a large area, “It is very important to dry the floor without deforming the floor.†Master Chen suggested that after the surface layer has been treated, the floor should be picked up from the gap of the expansion joint and covered with absorbent cloth. Dry it, put it in the shape of “wellâ€, place the bottom at the bottom, and put the floor on the reverse side to prevent the surface from cracking due to rapid drying. At the same time, it should be placed in a ventilated place to dry. Under normal circumstances, as long as the disaster is not serious, the rescue is timely, after the floor is dry, it can be reused by professionals.
Composite floor foaming combined strengthening and solid wood floor treatment method
The advantage of the composite floor is that it has both the stability of the reinforced floor and the natural feel of the solid wood floor on the floor surface. Master Chen suggested that: “The first-aid method after the composite floor is soaked in water is the combination of the treatment method of strengthening the floor and the solid wood floor. Although the waterproofness of the composite floor is better than that of the solid wood, the surface layer is pure solid wood. After soaking in water, it should be handled according to the actual situation."
If the water is small and the amount of water is small, dispose of the dry surface water as soon as possible, and use a vacuum cleaner or a blower to cool the water soaked in the gap between the floors. If a large area is immersed in water, the skirting line should be removed as soon as possible, and the submerged floor should be lifted. Also, the bricks or other things should be placed in a high space, and the floor should be stacked with a "well". At the same time, the open floor and the floor that is only submerged in water can be blown dry by means of a fan.
Pick
Nail Picking,Stainless Steel Nail Snips,Screw Shank Nail Stainless Steel,Carbon Steel Nail Clipper
YANGJIANG TRI-WIN INDUSTRY & TRADE CO.,LTD , https://www.triwintableware.com