Pre-construction preparation - material handling should be done properly
The so-called "three armed forces have not moved, grain and grass first", to do a good job, must be prepared in advance. Pre-construction preparation requires attention to material preparation and tool preparation.
A large basin of tiles on the balcony, when tiled, the fit of the tile to the wall is greater than the gravity generated by itself. Because the tile itself has many small holes, the water absorption capacity is strong, and the dry tile will absorb the moisture of the cement, so that the fitting degree is lowered, and the drum is easy to appear and fall off after the laying. Therefore, the tiles must be soaked for 24 hours until no bubbles appear, then dried and then laid.
The experienced seniors said that before the renovation, some households laid the tiles without shovel the putty. As a result, the cement could not be hanged and the tiles fell off. Therefore, before laying bricks, be very careful to inspect the wall and shovel the putty on the wall, so that the bricks are very secure.
Construction details - uniform paving need to be cautious
The paving process is very important, directly affecting the paving effect of the bathroom brick surface. There are many small details to be aware of during the paving process.
When the tiles are laid, the humidity of the cement mortar should be well grasped. Too dry or too wet will affect the adhesion between the tile and the wall. The cement mortar needs to be evenly and satisfactorily applied to the back of the tile to avoid smearing it all around. After the tile is attached to the wall, it needs to be hammered with a rubber hammer. At the same time, the tile should be inspected and the cement should be added or reduced in time. This process needs to be repeated until the tile and the wall are evenly fitted.
Due to the newly laid tiles, the cement is not completely dried and is easily sunk by gravity. Therefore, after the tile is attached to the wall, a certain gap must be reserved between the upper and lower tiles. If the retained gap is too small, it is easy to crack the glaze when the heat is expanded and contracted, reducing the service life of the tile.
When the tiles are laid, the tiles are dried and then caulked. If the tile is not completely dry, it will fill the seam, which will easily cause the tile to loosen and cause the tile to fall off, which will leave hidden dangers.
When paving non-whole bricks, first measure the size of the vacant position, determine the brick-laying method according to the number of tiles and the texture of the brick surface, and then cut the tile. For some tiles whose texture is not obvious, such as micro-powder bricks, pay attention to the directionality when laying them, so as not to make the walls messy.
Pay attention after construction - check and maintain should not be ignored
After the tile is laid, the maintenance of the tiles is also an important part of the construction. Protect yourself from the damage of the brick surface before use.
After 1 hour of tile tiling, use a towel to clean the brick surface of cement, caulking and other stains. Do not use a steel ball to clean afterwards, which will easily damage the brick surface.
After the tiles are laid, some follow-up works will be carried out. In order to avoid scratching the tiles during the construction, the tiled tiles must be protected after the wall coverings are completed. The box can be placed on the tile below the wall, avoiding the brick surface when moving the bathroom utensils and construction tools.
After the paving is completed for 12 hours, the flatness and verticality of the wall surface can be checked with a level gauge, and the tile is hit with a rubber hammer to check the empty drum condition of the brick, and it is found that the empty drum should be reworked immediately.
Baoji zhipu non-ferrous metal processing co., LTD. Main processing single crystal furnace, vacuum furnace, furnace, such as sapphire molybdenum, tungsten, tantalum, niobium tungsten bars, tungsten, Tungsten Plate thermal field, tantalum, tantalum, Tantalum Diaphragm, Tantalum Foil and other accessories processing, domestic use of the best quality raw materials, equipped with advanced equipment and professional production team, can be customized according to the requirements of all kinds of materials of Tungsten Products, welcome to inquire, looking forward to your cooperation!
Tantalum Foil
Tantalum Foil,Tantalum Diaphragm,99.95% High Purity Tantalum Diaphragm ,Good Stability Tantalum Foil
Baoji Zhipu Non-Ferrous Metals Processing Co., Ltd. , http://www.czpmow.com