Seiko fine wallpaper paving attention to many

Compared with the wall paint, the wallpaper has many advantages such as rich patterns, breathability, environmental protection, and cleanness. With the increasing demands of modern people for home living, many homeowners will choose wallpaper as the main decoration of the wall. However, the wallpaper's laying process directly affects the visual effect after finishing. Xiaobian will give you all the technical notes in each construction process and the acceptance after completion.

First, the wall surface treatment If the wall has seams, you need to use the putty to fill the seams, make up the seam with putty to add more white plastic (vinyl acetate resin), and then make up after sewing. If there is loose powder or dust on the wall, it should be removed by sanding. Too smooth a wall is not easy to absorb glue, and then the force will drop, and it must be sanded before wallpapering. After the above process is completed, a layer of base film is required to form a protective film between the wall surface and the wallpaper, which can not only protect the wall surface but also prevent water, salt, and alkali from permeating and corroding the wallpaper, thereby effectively protecting the decoration material from mold erosion. .

Second, glue preparation glue is generally made of wallpaper glue and white glue mixture, the viscosity is appropriate, easy to brush. The viscosity is adjusted by the amount of water added. The wallpaper powder is natural starch, and the white glue is synthetic resin (vinyl acetate resin). To ensure good wallpaper paste effect, different amounts of white glue are often added according to different wallpapers. The cloth surface of the cloth is thicker, and the glue preparation is thicker than other wallpapers. The white glue and wall powder below 15 ounces can be used to modulate. The product with 15 ounces or more can be used for special glue on the wall cloth. The special glue can be applied for 5 squares per kilogram. Meter.

Third, the wallpaper cropped to take a roll of wallpaper to open check the pattern, pattern, direction, to determine which direction is up, to kick the top of the floor tile as a starting point, with a tape measure accurate wall height, and then put the wallpaper on the table to start, painted With the glue facing upwards, with the pattern facing downwards, after measuring the length, use a pencil to draw a marking on the back, and then use the scissors to cut the pencil line. According to the wall section size, according to the wallpaper pattern spelling required to cut a good paper, numbered on the corresponding number, two set aside 30---50MM amount of cut, put for later use.

In the middle period of construction, the drum used for brushing the glue is soaked in the prepared glue for 30 seconds. Roller should be rolled in the same direction when the roller is brushed. Roller and wallpaper are lightly brushed at 45 degrees. Can't brush back and forth, so it's easy to wrinkle the wallpaper. When brushing, the movement should be smooth and uniform, holding the drum in one hand and the other hand fixed in the place where there is no brush; so as not to roll up the wallpaper. After all, use a small brush and apply a special glue (1:1 ratio of wallpaper and white glue) to the edge of the wallpaper.

After gluing the wallpaper, it will be affixed to the wall and it must be smoothed out to drive out the air bubbles. General plastic surface wallpaper is more washable, so you can use the "plastic scraper" to gently level the surface, drive out the bubbles, if a small amount of glue out of the surface, should immediately wipe clean with a wet sponge, scraper can not be too hard, or easy to scrape Injured surfaces cause print fading, reflection, and obvious seams. The surface of high-grade textile wall cloth is vulnerable to damage, as long as the brush is brushed gently with a short-bristle brush, and the amount of glue must be appropriate, and the glue must not be driven out of the seam to contaminate the surface, otherwise it cannot be processed. Paper wallpaper is very delicate and can only be used with short-bristled brushes. It should avoid glue sticking to the surface. If it touches the surface, it should be wiped clean immediately. Otherwise, the glue will not be removed after drying, and it will cause the disadvantage of color difference. When any wallpaper is used, the glue should not stick to the surface of the wallpaper, which is the most perfect construction process.

Post inspection content:

1) Whether the seams are aligned or not.

2) Whether there is a bubble.

3) Whether the pattern does not match.

4) crease remedy:

A, joints loose: use a knife to pick up the seams, inject glue from the slits, smooth with the scraper, wipe off the excess glue.

B. Bubbles: Cut with a utility knife, inject glue at the opening, and apply it to the flat surface to wipe off excess glue.

C, pattern does not match: due to inaccurate buildings, such as uneven foundation settlement, caused by flowers can not let it appear in the inconspicuous corner.

D, from the crease: Use a utility knife to cut creases, add glue, roll with the roller flat, if not flat, use "replenishment" method.

E, wet plaque: usually no wallpaper defects; may be a problem with the wall, to consult the relevant experts.

F, black spots: Most black spots indicate problems with the walls such as: mildew, water seepage, etc.; removing the wallpaper to deal with moisture, and then apply anti-mold glue.

Xiao Bian concludes: The various construction process of the wallpaper is one of the most important considerations, timely remediation of the problems found in the shop, pay attention to the timely acceptance, to ensure that there is no quality problems after the pavement.